Shenzhen Guangtong Optical Co.,Ltd

همه
  • همه
  • عنوان
خانه> محصولات> کابل میکرو دمیدن هوا> ریزگردهای HDPE> HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT

HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT

نوع پرداخت:L/C,T/T,Paypal,others,Cash
اینکوترم:FOB,CFR,CIF,EXW,FAS,FCA,Express Delivery
حداقل سفارش:1000 Meter
حمل و نقل:Ocean,Land,Air,Express
بندر:Shenzhen,Guangzhou

  • ویژگی های محصول
  • Packaging & Delivery
  • توضیحات محصول
  • توانایی تأمین و اطلاع...
  • Other information
ویژگی های محصول

مدل شمارهDB2

نام تجاریOEM

Diameter16/12 14/10 12/8 10/6mm

Lengthcustomization

Ovality (%, Before Coiled)5%

نام محصولmicroduct

MaterialHDPE

سرویس پردازشاکستاروژن

گزینه های رنگیسفید ، قرمز ، سبز ، آبی کاملاً رنگی

Usageunderground installation

ضخامت زیر مجرای2.0 میلی متر

ضخامت غلاف1.2 میلی متر یا سفارشی

Packaging & Delivery
فروش واحد: Meter
نوع بسته بندی: بسته صادرات استاندارد ، طول طبل 2000 متر یا سفارشی است
مثال تصویر:

The file is encrypted. Please fill in the following information to continue accessing it

توضیحات محصول
HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
توضیحات محصولات برای لوله میکرو مجرای HDPE :
Microduct HDPE 2 روش بسته بندی شده برای نصب الیاف هوا توسط Jetting Air.
بسته های میکروودکت متشکل از 18/14 ، 16/12 ، 14/10 ، 12/8 ، 10/6 ، 8/4 ، 7/3.5 ، 5/3.5mm زیر مجرای 5/3.5mm یا سفارشی. میکرودوکت داخلی به گونه ای طراحی شده است که انعطاف پذیر و سبک باشد ، اما در عین حال بادوام و آسان برای کنترل آن است. ریزگردها از ویژگی های اصطکاک کم مناسب در سطح داخلی برخوردار هستند.
نام محصول: میکرودوکت 2 راه ، لوله میکروودکت مستقیم دفن شده ، میکروودوکت دفن شده مستقیم در فضای باز
جزئیات تصاویر مربوط به میکروودکت لوله HDPE:
indoor microduct12 8 mm HDPE microduct2 way air blown fibre microduct
مشخصات لوله میکروودکت 7way:
Raw material:
HDPE of a high-molecular type with the following parameters is used for production of the microduct:
Melt flow index
0.1~ 0.3 g/10 minutes  (190 C , 2.16KG)
EN ISO 1133
Density:
Min. 0.940 g/cm3
ISO 1183
Tensile strength at yield:
Min. 21MPa 
ISO 527
 l Elongation at the break
 Min 350% 
ISO 527
 l Environmental stress crack  
resist (F50)
Min. 350 hours
ISO 4599
Physical and Mechanical Properties of Sub-duct 18/14mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
18.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 10mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 180mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 1800N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
216mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 16/12mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
16.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 10mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 160mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 1600N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
192mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 14/10mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
14.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 8.5mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 140mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 1350N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
168mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 12/8mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
12.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 8mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 120mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 1200N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
144mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 10/6mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
10.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 6mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 100mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 1000N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
120mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 8/4mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
8.0mm ± 0.1mm
3
Wall thickness
GTOC
2.0mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 5mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 80mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 720N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
96mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 7/3.5mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
7.0mm ± 0.1mm
3
Wall thickness
GTOC
1.75mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 5mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 70mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 630N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
84mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties of Sub-duct 5/3.5mm
1
Visual appearance
Visual inspection
Ribbed inside & smooth outside surface, free from blisters, shrink hole, flaking, scratches & roughness.
2
Outer diameter
GTOC
7.0mm ± 0.1mm
3
Wall thickness
GTOC
0.75mm ± 0.10mm
4
Inner diameter clearance
Blowing steel ball
A 3mm steel ball can be blown freely through the duct.
5
Ovality
GTOC
≤ 7%
6
Pressurization
5 minutes @12 bar each duct
No damage and leakage
7
Kink
IEC 60794-1-2 Method E10
≤ 50mm
8
Tensile strength
Rate of extension:
100mm/min
≥ 520N
9
Impact
IEC 60794-1-2 Method E4
1.0 J Impact, recovery time 1 hour
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
10
Min. bend radius
60mm
No residual deformation > 15% of inner and outer diameter, shall pass inner diameter clearance test.
Physical and Mechanical Properties (BUNDLE)
Tube Bundle
No. of ways
Outer Diameter
(Nom.)
Wall thickness
(mm)
Tolerance
(mm)
Max Tensile
(N)
HDPE 2x 18/14mm
2
38.4mm
1.2
±0.20
weight*G
HDPE 2x 16/12mm
2
34.4mm
1.2
±0.20
weight*G
HDPE 2x 14/10mm
2
30.4mm
1.2
±0.20
weight*G
HDPE 2x 12/8mm
2
26.4mm
1.2
±0.20
weight*G
HDPE 2x 10/6mm
2
22.4mm
1.2
±0.20
weight*G
HDPE 2x 8/4mm
2
18.4mm
1.2
±0.20
weight*G
HDPE 2x 7/3.5mm
2
16.4mm
1.2
±0.20
weight*G
HDPE 2x 5/3.5mm
2
12.4mm
1.2
±0.20
weight*G
*Customization service available for different sheath thickness or different number of sub-ducts.
hexatronic microduct
تکنیک تولید لوله میکروودوکت 4WAY:
Manufacturing Technique
Standards:
Crush performance
IEC 60794-1-2-E3
Tensile & elongation
IEC 60794-1-2-E1
Bend
IEC 60794-1-2-E11
Flexibility
IEC 60794-1-2-E8
Kink
IEC 60794-1-2-E10

ذخیره سازی:

بسته های تکمیل شده میکروودکت HDPE روی طبل ها را می توان حداکثر در فضای باز ذخیره کرد. 12 ماه پس از تاریخ تولید. دمای ذخیره سازی: -40 ℃ تا +70 ℃ دمای نصب: -20 ℃ تا +50 ℃ دمای کار: -40 ℃ تا +70
بسته بندی و تولید محصول:
low friction microduct24 way microduct
پروژه:
micro duct microductHDPE 1.2mm micro duct
توانایی تأمین و اطلاع...

بسته بندیبسته صادرات استاندارد ، طول طبل 2000 متر یا سفارشی است

بهره وری600000 Meter/Meters per Month

حمل و نقلOcean,Land,Air,Express

محل منبعچین

قابلیت ارائه600000 Meter/Meters per Month

گواهیISO,ROHS

کد HS3917210000

بندرShenzhen,Guangzhou

نوع پرداختL/C,T/T,Paypal,others,Cash

اینکوترمFOB,CFR,CIF,EXW,FAS,FCA,Express Delivery

خانه> محصولات> کابل میکرو دمیدن هوا> ریزگردهای HDPE> HDPE 2 WAY WAY OUTDOOR DIREPIAL PIPE MICRODUCT
  • ارسال پرس و جو

کپی رایت © 2024 Shenzhen Guangtong Optical Co.,Ltd کلیه حقوق محفوظ است.

ارسال پرس و جو
*
*

ما بلافاصله با شما تماس خواهیم گرفت

اطلاعات بیشتری را پر کنید تا بتواند سریعتر با شما در تماس باشد

بیانیه حفظ حریم خصوصی: حریم خصوصی شما برای ما بسیار مهم است. شرکت ما قول می دهد که اطلاعات شخصی شما را برای هرگونه مجوزهای صریح خود برای هرگونه گسترش فاش نکند.

ارسال